Search Results for '분류 전체보기'

125 POSTS

  1. 2008.09.22 spamcop.net 등록방법
  2. 2008.09.22 bl.csma.biz 등록 방법
  3. 2008.09.22 Junk Email Filter 등록 방법
  4. 2008.09.22 Cisco 3750 기본 셋팅
  5. 2008.09.22 KISA-RBL을 이용하는 방법
  6. 2008.09.22 라우터 관리를 위한 명령어

spamcop.net 등록방법

Posted 2008. 9. 22. 23:34


[spamcop.net]

 

 For Exchange 2003:

Make sure you install SP2 first, as it contains some important updates for Intelligent Message Filtering.

 

  • Display Name: spamcop
  • DNS Suffix: bl.spamcop.net

 

'Server > Mail Server' 카테고리의 다른 글

[SendMail] savemail panic in sendmail  (0) 2008.09.22
메일서버 장애 해결하기  (0) 2008.09.22
KISA-RBL을 Unix 계열에서 등록 방법  (0) 2008.09.22
DNSBL 등록 방법  (0) 2008.09.22
SORBS DNSBL 등록 방법  (0) 2008.09.22
bl.csma.biz 등록 방법  (0) 2008.09.22
Junk Email Filter 등록 방법  (0) 2008.09.22
KISA-RBL을 이용하는 방법  (0) 2008.09.22

bl.csma.biz 등록 방법

Posted 2008. 9. 22. 23:33

[bl.csma.biz]

We currently maintain two databases: bl.csma.biz and sbl.csma.biz. The first database contains only aggressive hosts that have spammed repeatedly during a short timeframe. The second database is a bit more aggressive, recording all hosts that have generated spam within a 45-day period.

Our recommendation is that the sbl.csma.biz list not be used for real-time DNSBL refusals because there is still a chance that messages could be legitimate. (See the SpamAssassin rules section for help here.)

 

DNSBL Queries
Query zone: bl.csma.biz
Returns: 127.0.0.2
SpamAssassin & Score-Based Queries
Query zone: sbl.csma.biz
Returns: 127.0.0.2

 

'Server > Mail Server' 카테고리의 다른 글

[SendMail] savemail panic in sendmail  (0) 2008.09.22
메일서버 장애 해결하기  (0) 2008.09.22
KISA-RBL을 Unix 계열에서 등록 방법  (0) 2008.09.22
DNSBL 등록 방법  (0) 2008.09.22
SORBS DNSBL 등록 방법  (0) 2008.09.22
spamcop.net 등록방법  (0) 2008.09.22
Junk Email Filter 등록 방법  (0) 2008.09.22
KISA-RBL을 이용하는 방법  (0) 2008.09.22

Junk Email Filter 등록 방법

Posted 2008. 9. 22. 23:32


[Junk Email Filter]

Our list server is hostkarma.junkemailfilter.com - this server returns several different results depending on what kind of listing it is. If the server returns 127.0.0.1 then it is whitelisted. You can accept the email without any further checking.

If the result is 127.0.0.3 then the host is yellow listed. Yellow listing means that host generates some spam and some nonspam. (examples, yahoo.com, hotmail.com) What that means is that this host should never be blacklisted and that other IP based blacklists should be bypassed to prevent false positives. If the result is 127.0.0.2 it is blacklisted - if the IP is listed here you can bounce it without further checking.

And if the result is 127.0.0.4 it is brownlisted which means it is on its way to being blacklisted but hasn't quite got there yey. But it might be worth a few points using SpamAssassin.

 

  • 127.0.0.1 - whilelist - trusted nonspam
  • 127.0.0.2 - blacklist - block spam
  • 127.0.0.3 - yellowlist - mix of spam and nonspam
  • 127.0.0.4 - brownlist - all spam - but not yet enough to blacklist

'Server > Mail Server' 카테고리의 다른 글

[SendMail] savemail panic in sendmail  (0) 2008.09.22
메일서버 장애 해결하기  (0) 2008.09.22
KISA-RBL을 Unix 계열에서 등록 방법  (0) 2008.09.22
DNSBL 등록 방법  (0) 2008.09.22
SORBS DNSBL 등록 방법  (0) 2008.09.22
spamcop.net 등록방법  (0) 2008.09.22
bl.csma.biz 등록 방법  (0) 2008.09.22
KISA-RBL을 이용하는 방법  (0) 2008.09.22

Cisco 3750 기본 셋팅

Posted 2008. 9. 22. 23:30

 

Cisco 3750

 

시스코 장비의 초기 패스워드는 전부 cisco 로 되어있습니다.

 

Privileged Mode(특권[관리자] 모드)

 

> enable

        Enter password : cisco

        #   <- 특권모드입니다.  셋팅에 관련된건 모두 특권모드에서 해야만 합니다.

 

 

콘솔로 들어가실려면 윈도우에서 지원하는 하이퍼터미널을 실행하셔야 합니다.

 

새연결(이름 아무꺼나 하셔도 됩니다)

연결대상에서  연결에 사용할 모뎀을 고르셔야 하는데 COM1(평균적으로 COM1을 많이 쓰입니다.)로 하시면 됩니다.

  

 

 

COM1 등록정보에서는

비트/ : 9600

데이터비트 8

패리티 없음

정비비트 1

흐름제어 없음을 하시면 됩니다.

 

 


 

그리고 확인을 누시면 Cisco3750으로 접속이 되실껍니다.

 

만약 접속이 되지 않는다면 통신포트를 바꾸어 주셔야 합니다.

 


 

1. 3750에서 VLAN을 나누는 방법입니다.

*vlan 2 설정*

SWITCH>enable

SWITCH#conf  termital

SWITCH(config)#vlan 2

SWITCH(config-vlan)#exit

SWITCH(config)#no vlan 2  <----- 지울때


 

2. 3750 장비에 ip를 설정할 수 있는데 ip를 설정하는 방법입니다.

설정된 VLAN을 가지고

SWITCH>enable

SWITCH#conf  termital

SWITCH(config)#interface vlan 2

SWITCH(config-if)#ip address 192.168.0.12 255.255.255.0

SWITCH(config-if)#no shutdown

SWITCH(config)#no interface vlan 2<----- 지울때

switch(config-vlan)#exit

switch(config)#ip default-gateway 10.10.10.1

 


 

3. 그리고 telnet 을 하려고 하는데 텔넷 설정하는 방법.

SWITCH(config)#line vty 0 4

SWITCH(config-line)#login

SWITCH(config-line)#password cisco


 


 

4. 그리고 생성된 vlan에 포트 할당 하는 방법

1번 포트를 vlan 2로 할당

SWITCH(config)#interface f0/1

SWITCH(config)#switchport access vlan 2

한꺼번에 할당하기(1번에서 5)

SWITCH(config)#interface range f0/1 - 5

SWITCH(config-if)#switchport access vlan 2


 


 

추가적으로 1~8은 디폴트
9~15
VLAN1, 16~24 VLAN2
이렇게 구성하려고 합니다.

SWITCH(config)#inter rang f0/9 - 15

SWITCH(config-if)#sw ac vlan 1

SWITCH(config)#inter rang f16~24

SWITCH(config-if)#sw ac vlan 2


 

참고로 시스코는 default vlan VLAN 1입니다.

그리고 시스코 스위치에 최초로 설정되어 있는 것은 VLAN 1이고

만일 포트에 다른 vlan을 할당하기 위해서는 먼저 vlan을 만들어야 합니다.


 

위처럼 설정하면 9-15번은 사실 설정을 하지 않아도 vlan 1번으로 할당 되어 있습니다.


 

확인 하는 방법은 SWITCH#show vlan  하시면 됩니다.

'Network > Cisco' 카테고리의 다른 글

Cisco TFTP 다운  (0) 2008.09.29
Switch Load Balancing  (0) 2008.09.29
라우터 관리를 위한 명령어  (0) 2008.09.22

KISA-RBL을 이용하는 방법

Posted 2008. 9. 22. 23:29

출처 : https://www.kisarbl.or.kr/

 

 

시작 > 프로그램 > Microsoft Exchange > System Manager 선택

 

 

전역설정 > 메시지배달 선택 후 마우스 오른쪽을 클릭하여 등록정보 선택
메시지 배달 속성에서 연결 필터링 탭을 선택 차단 목록 서비스 구성에서 추가를 클릭
연결 필터 규칙정보에서 표시이름, 공급자의 DNS 접미사를 작성
예)표시이름 : KISARBL
    공급자의 DNS 접미사 : spamlist.or.kr

 

 

차단목록서비스구성에서 편집을 클릭

 

 

필터규칙을 다음 마스크에 일치 127.0.0.1 입력확인 버튼

 

 

서버 > 서버명 > 프로토콜 > SMTP > Default SMTP Virtual Server 선택 후 마우스 오른쪽을 눌러서 등록정보 선택
일반탭에서 IP주소영역의 고급클릭

 

 

고급정보에서 편집를 선택
구분정보에서 IP 주소의 지정하지 않은 모든 (IP)를 선택하면 IP리스트가 나오는데 여기서 받는 메일 서버의 IP 선택 연결 필터 적용 체크한 후 확인
위와 같이 작성 후 확인을 선택하시면 모든 설정이 완료됩니다.

 


'Server > Mail Server' 카테고리의 다른 글

[SendMail] savemail panic in sendmail  (0) 2008.09.22
메일서버 장애 해결하기  (0) 2008.09.22
KISA-RBL을 Unix 계열에서 등록 방법  (0) 2008.09.22
DNSBL 등록 방법  (0) 2008.09.22
SORBS DNSBL 등록 방법  (0) 2008.09.22
spamcop.net 등록방법  (0) 2008.09.22
bl.csma.biz 등록 방법  (0) 2008.09.22
Junk Email Filter 등록 방법  (0) 2008.09.22

라우터 관리를 위한 명령어

Posted 2008. 9. 22. 22:42

>>>>  라우터 관리를 위한 명령들.... <<<<

>>> TFTP Server 설정...

 

>>> running-config 를 TFTP 에 Backup 하기

R1#copy running-config tftp
Address or name of remote host []? 192.168.2.2
Destination filename [r1-confg]? R1-Config
!!
1089 bytes copied in 5.516 secs (217 bytes/sec)
R1#

 

>>> TFTP에서 Running-config를 복구할 때는 먼저 Ethernet Interface에 IP 설정을 해서
      TFTP서버와 통신이 가능한 상태에서 진행한다...
R1#copy tftp running-config
Address or name of remote host []? 192.168.2.2
Source filename []? R1-Config
Destination filename [running-config]?
Accessing tftp://192.168.2.2/R1-Config...
Loading R1-Config from 192.168.2.2 (via Ethernet0): !
[OK - 1089/2048 bytes]

1089 bytes copied in 5.76 secs (217 bytes/sec)
R1#

 

>>> IOS Backup 하기

1. flash에 IOS Name을 체크한다.
R1#sh flash

System flash directory:
File  Length   Name/status
  1   5721700  c2500-i-l.120-8b.bin 
[5721764 bytes used, 2666844 available, 8388608 total]
8192K bytes of processor board System flash (Read ONLY)

 

2. flash에서 TFTP로 copy 해서 IOS를 백업한다.
R1#copy flash tftp
Source filename []? c2500-i-l.120-8b.bin
Address or name of remote host []? 192.168.2.2
Destination filename [c2500-i-l.120-8b.bin]?
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
5721700 bytes copied in 70.232 secs (81738 bytes/sec)
R1#


>>>  C2500 시리즈 IOS 업그래이드 하기

1. config-register값을 0x1 로 변경한다.
 Router(config)#config-register 0x1
 Router(config)#exit
 Router#reload

 

2. 먼저 enable 한후 설정 상태를 확인한다. TFTP서버와 통신이 되는지 검사...
R1(boot)>en
Password:
R1(boot)#sh ip int bri
Interface        IP-Address      OK?  Method    Status                 Protocol
Ethernet0        192.168.2.1    YES  NVRAM     up                     up     
Loopback0      192.168.1.1    YES  NVRAM     up                     up     
Serial0            192.168.3.2    YES  NVRAM     up                     up     
Serial1            unassigned     YES  not set     administratively down  down   
R1(boot)#ping 192.168.2.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/203/1000 ms


R1(boot)#copy tftp flash

System flash directory:
File  Length   Name/status
  1   5721700  c2500-i-l.120-8b.bin 
[5721764 bytes used, 2666844 available, 8388608 total]
Address or name of remote host [255.255.255.255]? 192.168.2.2
Source file name? c2500-i-l.120-8b.bin
Destination file name [c2500-i-l.120-8b.bin]?
Accessing file 'c2500-i-l.120-8b.bin' on 192.168.2.2...
Loading c2500-i-l.120-8b.bin from 192.168.2.2 (via Ethernet0): ! [OK]

Erase flash device before writing? [confirm]
Flash contains files. Are you sure you want to erase? [confirm]

Copy 'c2500-i-l.120-8b.bin' from server
  as 'c2500-i-l.120-8b.bin' into Flash WITH erase? [yes/no]yes
Erasing device... eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee ...erased
Loading c2500-i-l.120-8b.bin from 192.168.2.2 (via Ethernet0): !!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK - 5721700/8388608 bytes]

Verifying checksum...  OK (0x788F)
Flash copy took 0:02:50 [hh:mm:ss]
R1(boot)#

 

>>>  Cisco IOS 복원하기 (1600, 1700 , 2600 시리즈등...)
! TFTP 서버를 사용하는 경우
Example
     rommon 1 > IP_ADDRESS=171.68.171.0
     rommon 2 > IP_SUBNET_MASK=255.255.254.0
     rommon 3 > DEFAULT_GATEWAY=171.68.170.3
     rommon 4 > TFTP_SERVER=171.69.1.129
     rommon 5 > TFTP_FILE=c2600-is-mz.113-2.0.3.Q
     rommon 6 > tftpdnld

               IP_ADDRESS: 171.68.171.0
           IP_SUBNET_MASK: 255.255.254.0
          DEFAULT_GATEWAY: 171.68.170.3
              TFTP_SERVER: 171.69.1.129
                TFTP_FILE: c2600-is-mz.113-2.0.3.Q

     Invoke this command for disaster recovery only.
     WARNING: all existing data in all partitions on flash will be lost!
     Do you wish to continue? y/n:  [n]:  y

     Receiving c2600-is-mz.113-2.0.3.Q from 171.69.1.129 !!!!!.!!!!!!!!!!!!!!!!!!!.!!
     File reception completed.
     Copying file c2600-is-mz.113-2.0.3.Q to flash.
     Erasing flash at 0x607c0000
     program flash Location 0x60440000
     rommon 7 >reset

 

! Console 포트를 사용하는 경우
1. 먼저 라우터에 Xmodem 포트 설정을 한다.
rommon 1 > confreg
do you wish to change the configuration? y/n [n]:  y
enable  "diagnostic mode"? y/n  [n]:
enable  "use net in IP bcast address"? y/n  [n]:
disable "load rom after netboot fails"? y/n  [n]:

enable  "use all zero broadcast"? y/n  [n]:
enable  "break/abort has effect"? y/n  [n]:
enable  "ignore system config info"? y/n  [n]:
change console baud rate? y/n  [n]:  y
enter rate: 0 = 9600,  1 = 4800,  2 = 1200,  3 = 2400
            4 = 19200, 5 = 38400, 6 = 57600, 7 = 115200  [7]:  7
change the boot characteristics? y/n  [n]:  y
enter to boot:
 0 = ROM Monitor
 1 = the boot helper image
 2-15 = boot system
    [0]:  0

    Configuration Summary

enabled are:
load rom after netboot fails
console baud: 115200
boot: the ROM Monitor
do you wish to change the configuration? y/n  [n]: n
You must reset or power cycle for new config to take effect

 

2. Xmodem을 초기화 한다.
rommon 2 > xmodem -c c2600-is-mz.122-17.bin
Do not start the sending program yet...
         File size           Checksum   File name
 

3. 명령어를 입력한 다음

Terminal Client 프로그램에서 파일을 전송한다.

 

 

>>> 암호 복구 하기

1. 라우터에 콘솔 연결을 먼저 한다.
2. 라우터에 전원을 켜고 60초 이내에 [Ctrl + Break] or [Ctrl + B]를 누르면 다음 모드로 이동한다.
********************************************************************************************

<<<<< 2500 Serise >>>>>>
Abort at 0x10E5C1E (PC)
>

 

3. Register값을 0x2142로 변경한 후 재시작한다..
    (이 값은 NVRAM을 로드하지 않고 라우터 부팅을 한다.)
>o/r 0x2142
> i

 

<<<<< 16xx, 17xx, 26xx Serise 등 >>>>>>
rommon1>

 

3. Register 값을 0x2142로 변경후 재시작한다.
rommon1>confreg 0x2142
rommon2>reset
********************************************************************************************

 

4. NVRAM을 Pass하고 부팅하기 때문에 Setup Mode로 시작한다. Ctrl + C 로 Setup Mode를
    취소하고 라우터에 CLI Mode로 접근한다...

         --- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]:


Press RETURN to get started!
<생략>
Router>

 

5. 라우터에 Privileged Mode로 이동 후 startup-config 를 running-config로 load 한다.

Router>en
Router#copy startup-config running-config
Destination filename [running-config]?
1089 bytes copied in 4.952 secs (272 bytes/sec)
R1#

 

6. 라우터에 기존에 설정되어 있던 Setting 정보가 복구되면 각 인터페이스 정보를 확인한다.
    startup-config에서 running-config를 강제 복구시 인터페이스가 활성화 되지 않는다.
    직접 각 인터페이스로 이동후 활성화를 한다....no shutdown를 입력해준다...
R1#sh ip int brief
Interface              IP-Address      OK? Method Status                Protocol
Ethernet0             192.168.2.1     YES TFTP   administratively down down   
Loopback0           192.168.1.1     YES TFTP   up                    up     
Serial0                 192.168.3.2     YES TFTP   administratively down down   
Serial1                 unassigned      YES unset  administratively down down   
R1#conf t
R1(config)#int e0
R1(config-if)#no shutdown
R1(config-if)#int s0
R1(config-if)#no shutdown


7. 잃어버린 암호를 다시 설정한다.  (설정하고자 하는 암호를 입력한다.)
Router(config)#enable secret cisco

 

8. Register값을 원래대로 변경한다.  0x2102가 대부분 기본 값이다....
    이 정보는 각 라우터에서 먼저 show version으로 체크한 후에 기록해 놓는 것이 바람직하다..

Router(config)#config-register 0x2102

 

9. 이제 수정된 정보를 저장하고 다시 시작하면 완료된다.

Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]

R1#reload
Proceed with reload? [confirm]

 

완료>>>>>

'Network > Cisco' 카테고리의 다른 글

Cisco TFTP 다운  (0) 2008.09.29
Switch Load Balancing  (0) 2008.09.29
Cisco 3750 기본 셋팅  (0) 2008.09.22
« PREV : 1 : ··· : 15 : 16 : 17 : 18 : NEXT »